7 Quad Rear View Backup Side Camera System Cctv For Truck, Motorhome, Forklift

This wired two-camera system is complete with a crystal clear 7 Quad LED Digital Panel color monitor with distance grid lines and mirror image capability, a power harness, one 120° color CCD cameras with 50 foot infra-red night vision and all the wires, connectors and mounts you will need. With built-in system memory, this innovative system automatically saves previous option settings even after it's turned off. This system has two viewing options. The camera view can be triggered when the vehicle is put into reverse, or remain on continuously.

IT CAN BE USED FOR FARM TRACTOR, SCHOOL BUS, GARBAGE TRUCK, SWEEPER, AGRICULTURE EQUIPMENTS, HEAVY EQUIPMENTS, MOTORHOME TO ELIMINATE THE BLIND SPOT BEHIND THE VECHILES. 7 WIRED QUAD VIEW MONITOR1. CCD WATERPROOF NIGHT VISION CAMERA. 15METERS EXTENSION CABLE WITH 4 PIN CONNECTOR1.

10METERS EXTENSION CABLE WITH 4 PIN CONNECTOR1. 1.7 quad TFT LCD monitor with U-type bracket, 16:9 and 800 x 3(RGB)X480.

Separatedly set each camera's mirror/normal image. Image also can be turned up-side-down. Automatic blue backlight for buttons. Support up to 4 video inputs at the same time, 4way trigger wires. Monitor only supplies camera which is in use with DC12V, Energy saving. Monitor display cameras in various modes, such as single(full screen) view, double view, tri-view and quad view. Distance gride line can be turned on or off by menu. Aviation 4-pin connectors with screw-lock. Monitor can display cameras in single(full screen) view, double view, tri-view and quad view by press the buttons on the panel. Image can be rotated by menu to make it to be mirror/normal/up-side-down image. 7 Inch Wired Quad Color LCD monitor. Resolution: 800 3(RGB)480. Support 4 cameras video input at the same time. Separate trigger control wires for each camera. Menu to set up reversing image delay time 0-15s, mirror/normal image. Monitor will automatic switch-over the image to related camera and back to. The original mode when the trigger stops.

In standby mode, monitor will turn on automatically when triggered and will switch to back up camera image, Trigger end after shutdown. Built-in short-circuit protector When installing and connecting the kit, people connects the female 4-pin connectors to the male one from the camera and monitor, they sometimes connect the video pin of the camera to the power pin of the monitor. It may cause a short-cut, the built-in protector may keep the monitor away from being burnt. 2.120 degree viewing angle.

Aviation 4-pin connector with screw-lock. Sensor:1/3 Sharp Color CCD.

Video format: PAL / NTSC optional. Waterproof Rate:IP69K, (Micro-dust can not come into the inside of the camera, and the camera can resist the high pressure water of 10000KPa from the spray nozzle, and no water come into the camera at all). Shell material: aluminum alloy camera never gets rusty, and has a higher ability in heat radiation than iron housing.

Dustproof, waterproof, hydrochloric acid prevention, explosion prevention. It usually takes about 3-7days to arrive any countries in the world. This item is in the category "Consumer Electronics\Vehicle Electronics & GPS\Car Video\Rear View Monitors/Cams & Kits".

The seller is "truckcamsolution" and is located in this country: CN. This item can be shipped worldwide.

Camera Connection Type: Wired
Compatible Vehicle Make: Universal
Screen Display: TFT - LCD
Country of Manufacture: China
CAMERA: 1/3\
Type: Rear View Monitor w/Cam Kit
POWER INPUT: DC12V-36V
CABLE LENGTH: 15METERS*1, 10METERS*1
MPN: 044806
Brand: AutoPal
Screen Size: 7\
UPC: 602938044806